Please follow the instructions below to ensure that the units are configured correctly. Switching it on automatically puts it into pairing mode. For full instructions on the receiver pairing refer to the RXRT manual.
See page 7. See page See page 9. To access the Menu screens, press the OK key twice. The first menu displayed is the PROGRAM menu: Use the Touch Ring to scroll through the Menus, and press the OK key to select the menu you want to use: You can scroll through the menus in either direction forwards or backwards depending on the direction you move your finger around the Touch Ring. The menus are displayed in the order shown in the picture above.
Press the OK key to start sending the RF address code to the receiver. The STTX display will change to show a rundown timer: The unit counts down for a period of 10 minutes, with the RF Signal indicator flashing while the signal is being transmitted. If the Red LED changed state after 10 minutes, repeat the whole pairing process.
Pressing and holding the SYNC button on the receiver will not clear the RF address code saved into the internal memory, and switch the receiver into learning mode, as previously described. The receiving range between thermostat and receiver is metres in open air, however many factors can affect the RF transmission and shorten the operating distance, e.
The operating range is generally around 30 metres, which is large enough for most household applications, but it is advisable to test the RF transmission from the intended thermostat location to the receiver location before fixing the thermostat to the wall. The RF communication is one way, from the thermostat to the receiver — the receiver does not send any signal back to the thermostat.
The RF signal indicator only flashes once when a signal is being transmitted. The thermostat will transmit only when there is a need to control the heating system. Will transmit once every twelve minutes. The Touch Ring surrounds the programmable thermostat display, and is operated very easily by moving your finger around the ring. The backlit Liquid Crystal Display LCD gives a highly visible, easily readable indication of the programmable thermostat status. The programmable thermostat has a default set of Programmes that have been designed to meet the needs of most users.
If these default programmes are not suitable for your particular situation, reprogramming the STTX with your own settings is a very straightforward operation. Initially, the Weekdays will be selected and flashing — you can scroll through all the various options for day selection Weekdays, Weekend, 7 days, or individual days by using the Touch Ring.
As usual, pressing the OK key will select the desired option. These screens allow you to set the required time and temperature settings to provide optimum control for your heating system. Using the Touch Ring, scroll up or down to adjust the hour to the required setting and then press the OK key to confirm. Change this setting using the Touch Ring in the same way that you changed the hour setting, confirming your setting with the OK key.
Finally, set the desired temperature setting by scrolling with the Touch Ring and again confirm with the OK key. Continue to add your desired settings for each of the programmes through to Programme 6 in the same way as Programme 1 hour, minutes, and temperature. If you decide to enter settings for individual days rather than Weekdays or Weekends, the STTX also offers a time saving COPY function that allows the user to copy settings from one day to another.
On this screen, scroll to the day that you want to copy the settings to using the Touch Ring, and then confirm this by pressing the OK key. The STTX will then move to the next day and ask if you would like to copy again. In the example here, Monday has been programmed, and the next day that has not been programmed is Tuesday. Once the settings for Tuesday have been programmed by copying, the settings can then be copied to Wednesday, and so on.
Please be aware that each of the programme time settings must be in sequence: for example, Programme 3 cannot be set with a time earlier than Programme 2. If this situation occurs, then the STTX may operate in an unpredictable way. The HOLIDAY mode allows the user to override all the current Programme settings with a specific temperature setting that is active between two dates entered by the user.
To start entering the Holiday Override settings, press the OK key once. Use the Touch Ring to scroll to set the date and confirm the choice using the OK button. Use the Touch Ring to set the preferred temperature and confirm the choice using the OK button.
Pressing the Touch Ring will change the display to show the current temperature setting, but this setting cannot be adjusted while in this mode. This will display the current set temperature. The set temperature will be displayed for two seconds before the LCD changes to display the room temperature again. Use the Arrow key to return to the Menu Option display. Press the OK key to confirm the setting. The currently set temperature will be displayed on the LCD and will flash.
When the set temperature is flashing, press the Touch Ring and move your finger clockwise to increase the set temperature, or anti-clockwise to decrease the set temperature.
Press OK at any time to confirm the selection. Note that the set temperature display will not flash while being adjusted — this is normal and the display will start to flash again approximately 0. The manual setting will remain in effect until the next programme time is reached, programme or clock settings are changed, an operating mode change is detected or the Manual Override mode is cancelled.
The first option within the menu is a choice of 12 or 24 hour clock setting. On entering the menu, use the Touch Ring to scroll to the preferred option 12 or 24 hour clock , and confirm the choice using the OK button. Use the Arrow key to return to the previous screen display.
After setting the time display format, the next screen display allows you to set the time. Use the Touch Ring to scroll to set the hour and confirm the choice using the OK button. The minute setting will then be selected — change this setting in the same way using the Touch Ring, and confirm the setting using the OK button.
After setting the time, the next screen display allows you to set the date — this is set in exactly the same way as previously described for the time. After setting the date, the next screen display allows you to set the daylight saving time DST option. It is strongly recommended that you familiarise yourself with the instructions contained in the Operation section of this manual before attempting to change any of the settings in the SERVICE menu.
During commissioning the installation engineer has the option to enter either his Mobile or Office telephone number as both a reminder when the system is due to be serviced, and as a way for the home owner to make contact when the service is due.
To access the Menu screens, press the OK key once. This allows the product to control the Heating or Cooling systems. The factory default setting is HEAT, details on how to change the default setting for a cooling application can be found below. Firstly you need to enter a unique PIN code, when the first digit flashes scroll to set the first digit and press OK to confirm the repeat for the other two digits Once all digits have been entered, press OK to confirm or the arrow key to return to previous digit or previous display.
The service code is total 3 digits, from to Once the code has been entered, the next menu screen allows you to set the next service date for the system. If you wish to configure the STTX for a cooling application. Confirm the setting using the OK key, or Press the Arrow key to return to the previous screen display. The next menu screen allows you to set a temperature setting. This temperature is the maximum temperature that the heating system will operate at once the previously set service date is reached.
The temperature is set by scrolling the Touch Ring to the desired setting, then confirming with the OK key. After enabling SERVICE mode, there is a screen that will allow you to enter an 11 digit number — this feature is intended for you to enter your telephone number so that the end user can contact you when the next service is due.
The number is entered in the same way as the code — scroll with the Touch Ring until you reach the required number, then confirm by pressing the OK key. After entering and confirming the last digit with the OK key, store the telephone number by pressing the Arrow key Once set as described, the SERVICE indicator will appear on the display 30 days before the set date. The display will no longer display the operating mode, only the telephone number that has been entered and the SERVICE indicator which will continue to flash.
PWM mode should only be selected by the Engineer carrying out the installation or other qualified person. The RCC status indicator will be displayed for 10 minutes during clock updates. The indicator will flash during the time update process, after which the indicator will be displayed for 5 minutes before turning off. The time and date will also be automatically updated when the STTX is powered up, or after the Reset Button is pressed.
These instructions are applicable to the Salus Controls model stated on the front cover of this manual only, and must not be used with conformity is available at the following internet address: saluslegal. Free delivery on eligible orders of? S-Series Digital Thermostat.
STRF Thermostat pdf manual download. Join Co-production practitioners network. Sign Up or Sign In. Powered by. Badges Report an Issue Terms of Service. Co-production practitioners network A network for co-production practitioners. Blogs Forum.
0コメント